Here are some ways to deal with the reflective and relatively beautiful plastic of a car: - ** Use light-proof pad or reflective film **: - When some hard plastic models reflected light, the light-proof pad could play an anti-reflective role. Moreover, most of the car's center console was made of slush plastic material. Although the reflection was not as strong as hard plastic, the light-proof pad also had a certain effect. There was also the Magotan's central control reflective film, which did not block the atmosphere lights and did not leave any glue, which could reduce the reflection. - For the reflection of the car film, you can replace the heat insulation film with a low reflection rate (9% or less) to reduce the reflection. - ** Use decorative items **: For example, stick a red flag reflective car sticker with a certain aesthetic reflective sticker, which can reduce the reflection and also play a role in decorating the car. Read more exciting novels for free
The reflection of the car recorder was very annoying. If you want to keep an eye on the reflection of the car recorder, you can do this. First, check its installation position to see if there was anything reflecting light nearby. If there was, adjust the position or move the reflective thing away. Also, check if the lens of the recorder is dirty. If it's dirty, wipe it clean. Maybe it won't reflect light anymore. Also, he could put an anti-reflective film on the recorder lens, just like the film on a mobile phone. It might work. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
If the car camera is reflecting light in the sun, you can refer to the following methods: 1. ** Adjusting the camera angle **: When installing the camera, adjust its position to avoid direct sunlight. For example, when installing it at the door, do not face the door. It can be installed in the corner of the wall on the same side as the door. 2. ** Choose a suitable camera **: You can choose a camera with the function of suppressing backlighting. For example, a super dynamic camera can improve the backlighting phenomenon to a certain extent. It can also improve the backlighting problem with a large contrast in the picture. This camera can also be used for the license plate camera. 3. ** Add fill light method **: Add fill light to solve the problem of backlighting. 4. ** Dealing with special situations **: If the license plate recognition is white and the camera's infrared light is directly shining on the license plate, you can turn off the camera's infrared light and add a white fill light.(Because the infrared camera is not recommended for license plate shooting, the infrared reflection will not be able to capture the license plate); If the car lights shine on the camera and cause the reflection, you need to adjust the camera's installation angle and stagger it from the direction of the car to avoid direct light. If the camera has a strong light suppression function, you can turn it on.(When choosing the license plate recognition camera, you should pay attention to the parameters. If you choose the camera with strong light suppression function, you can directly enter the web to set the camera with this function.) <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
The reflection in the car can be eliminated by the following methods: 1. ** Elimination of the reflection on the center console ** - Do not place light-colored reflective things such as paper on the center console; - Go to the auto parts city to buy the corresponding model of the center console pad (materials include silica gel, leather, microfiber velvet, etc.). The center console pad can make the surface of the center console not smooth, reduce reflection, and effectively prevent reflection. Generally, dozens of yuan can solve the problem; - If the new car had not yet been attached with a glass film, the film on the front windshield should be of good quality and of a large brand to ensure various indicators and parameters, to avoid reflection due to poor film quality, and to prevent the line of sight from being affected when driving at night; - Even if the center console was covered with a light-proof pad, do not place too many things. Otherwise, when the light was good, the items would still be reflected on the front windshield, and it was not safe to place too many things. 2. ** Eliminating the reflection of the air conditioner's air outlet ** - For the reflection of the air conditioner vent (such as the silver decorative air conditioner vent is easy to reflect light on the door glass), you can stick a sticker on the vent position, which is both beautiful and effective to avoid reflection; - He could also try to get used to the reflection. 3. ** Elimination of reflection at the air outlet of the air conditioner ** - For the situation where there is an atmosphere light and the air outlet of the air conditioner is reflective (because the atmosphere light is brighter, the window is darker after the film is applied, and there will be reflection on the glass), you can turn off the atmosphere light to avoid reflection; - Or, just like how he dealt with the reflection from the air conditioner's vent, he had to adapt to the impact of this reflection. 4. ** Eliminating the reflection of the wind mask on the door panel ** - If the windshield cover at the door vent is reflective (for example, a smoother and brighter windshield cover), you can spray a black hand paint before the windshield cover is attached to reduce the reflection (Matt black paint may be better). <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
If you encounter a mirror reflection in photography, you can deal with it by the following methods: 1. Using a Polarizer: Turn the filter around and adjust it to the right position to minimize the reflection. However, if there was a superimposing effect of two pieces of polar mirrors (such as the polar glass windows of some high-rise hotels), there might be a color deviation problem. 2. Post-processing in Ps: - If the reflective area of the mirror lost its own color, you could use the [S] shortcut key to copy a similar color to cover the original white point. - You can also use the Pen Tool to create a path along the inside of the mirror, then press Control +Enter to convert it into a selection and feather it appropriately. Create a new layer and fill it with a linear fade (the color can be selected according to the specific situation, and the Opacity can be reduced appropriately). Then, create a color level (shortcut key: Control +L) or drag the left and right color level slide bars to the center through the new fill (black and white circle icon) at the bottom of the layer panel to increase the contrast. Finally, select the new linear fade layer and add a layer mask. Use the black brush tool to smear the parts that need to be shown (such as the eyes). 3. Operation during filming: - Dim the indoor lights: If you want to take photos through the window of the room, dim the indoor lights to form a contrast with the outdoor environment to reduce reflection. - Wear dark-colored clothes to reduce the reflective surface area. - Shooting close to the window: Try to shoot as close to the window as possible (when using a DSLR, be careful not to let the lens touch the glass to prevent it from getting dirty). - Avoiding the use of super wide-angle lenses because the field of view of super wide-angle lenses is wider and it is easy to produce reflections. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
There were many types of reflective car sticker. From the material point of view, the engraving type reflective material was better. It was not sticky but the price was high. The printing type was easy to stick to the paint and easy to fall off, so the price was lower. Reflective car sticker can be used for car exterior decoration. It is a simple modification method. People can publicize themselves through customized text and patterns, making the car more warm and fashionable. In terms of affixing, the reflective logo on the car body was divided into rear affixing and side affixing, with different requirements. When the reflective logo on the rear body is pasted, it should reflect the width and height of the rear of the vehicle as much as possible. The horizontal paste should reflect the width, and the vertical paste should reflect the height. The intersection of the corners at the rear of the cargo compartment should be white units (except for special circumstances). Different grades of body reflective marking materials should not be used at the rear of the vehicle at the same time. When Class 1 or Class 2 body reflective marking materials are used, the sum of the area of the body reflective marking material and the rear reflective device should have a corresponding standard. There were also requirements for the length of each continuous segment and the paste interval. Special circumstances allowed the red and white units to be pasted separately, but the red and white units must also be maintained with length and interval requirements. If it cannot be pasted vertically along the two sides of the rear of the carriage, it can be pasted on the surface that is close to the edge and has a width of 50mm, and the upper edge should be as close as possible to the upper edge of the rear of the carriage. The reflective label on the side of the car body is allowed to be interrupted. The total length (excluding the interval part) has the requirements of the vehicle length ratio. The length of each continuous segment, the number of red and white units, and the interval of the attachment are also specified. The length of the reflective label on the side of different types of vehicles has different standards. The body reflective marking on the side of the van and van trailer should reflect the outline of the cargo compartment. The level of the body reflective marking material on the side can be different from the rear body reflective marking material. There were also some innovative reflective car sticker products on the market, such as LED car light sticker, which could be customized and changed color with a small remote control. It could also be combined with some special devices to create a cool effect. On social media platforms such as TikTok, topics related to car sticker, especially reflective sticker, were highly viewed, which also reflected its popularity among car enthusiasts. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
If the film reflected light, it might be caused by the poor quality of the film and the high reflection rate. In this case, the only solution was to remove the inferior glass film and then reapply the film. When re-filming, you should pay attention to the quality. You can consult the sales staff of the glass film store or the technician of the film car beauty store. Choose a high-quality car film with a small reflective rate. Don't choose a low-quality film because of the low price. In addition, if the rearview mirror was severely reflective after the car door glass was covered with a film, you could consider changing the film or tearing it off. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
If the reflection of the license plate is not clear, there are the following situations and solutions: 1. The reflection of the license plate was caused by the camera's infrared light shining directly on the license plate. At this time, you can turn off the camera's infrared light and add a white fill light. Generally, infrared cameras are not recommended for license plate shooting because infrared reflection may not be able to capture the license plate. 2. The car lights caused the license plate to reflect light: The car lights shone on the camera, causing the license plate to reflect light. In this case, you need to adjust the camera's installation angle to a certain angle from the direction of the car to avoid direct light, and turn on the camera's strong light suppression function (If the camera has this function, you need to check the parameters to confirm when choosing the license plate recognition camera. Cameras with strong light suppression can be set up directly on the web. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Here are some ways to deal with reflections in window photos: - ** Adjusting the indoor lighting and environment **: If you want to take photos through the window of the room, the ideal way is to dim the indoor lighting to contrast with the outdoor environment. Because if the indoor light is stronger than the outdoor light, there will inevitably be reflection. If the lighting situation cannot be changed, you can pull the curtains and only expose the lens. The curtains can block the indoor light to improve the shooting effect. - ** Clothes choice **: Wearing dark colored clothes, although it can't completely solve the reflection problem, it can reduce the reflection area and make the photo effect relatively better. You must avoid wearing light-colored clothes, otherwise the photo effect taken under the sun will be very poor. - ** Shooting position adjustment **: Try to shoot as close as possible to the window, but if you use a single-lens reflex camera, be careful to prevent the lens from touching the glass and getting dirty. - ** Choice of lens **: Try to avoid using a super wide-angle lens because it has a wide field of view and increases the probability of capturing reflective objects. - ** Use Polarizing Mirror (Limited)**: You can use a Polarizing Mirror if you have the conditions. It can eliminate the reflection of non-metallic objects to a certain extent. When using it, rotate the filter once and adjust it to the right position to eliminate the reflection to the greatest extent. However, there were many limitations to using a prismatic lens. For example, when the shooting direction was not at a 45-degree angle with the reflective surface (such as an 80-degree or 90-degree angle), the extinction effect of the glass from the vertical direction might be almost zero; When taking pictures through double-layered glass (such as airplane glass), the picture would appear rainbow; Under cloudy and sunny backlighting conditions, and when the lens was wide-angle on a sunny day, the effect was not good. - [Self-made artifact (suitable for cameras and mobile phones): Can be made from a tight rootless dark (black or navy blue) stockings, a ring for a hoop, and a number of clips.] First, the ring was implanted inside the stockings, and then the socks and ring were fixed with a long tail clip. Then, the middle circle was carefully cut to form a trumpet shape. Because one end of the sock was tight, it could be fixed on the lens, and the other end could be fixed on the glass. The aperture of the camera needed to be adjusted (because it could only block the reflection and not the dirty things on the glass. Increasing the aperture could make the dirty things virtual). If the lens was small, the socks could be tied with a pressure belt when they were loose. - ** Use mobile phone extinction cover (only applicable to mobile phones)**: There is an anti-reflection artifact specially developed for mobile phone photography. When shooting, stick close to the glass and eliminate the reflection of the glass through physical means. There are two models of mobile phone extinction cover, which can be used to fit models with cameras in the middle or side. The soft and non-damaging silica gel material has good malleability, which can be used to fit most models. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
Here are some ways to deal with reflections in window photos: 1. ** Use a Polarizing Mirror (suitable for cameras)**: Turn the filter around and adjust it to the right position to eliminate the reflection to the greatest extent. 2. [Self-made tool (suitable for camera lens): You can use a black stocking to fix the lens to reduce the reflection.] 3. ** Change the state of the glass (suitable for indoors)**: Indoors, spray some water on the glass with a watering can, and then use a tool with a flat cross-section (such as a putter knife) to scrape slowly to avoid bubbles. Scrape from bottom to top. 4. ** Using deep learning technology (with the help of relevant software or equipment)**: The researchers proposed a learning method based on the difference in motion between the background and the background. Through deep learning, alternating optical flow field estimation and image reconstruction to achieve high-quality obstruction removal (reflection can be regarded as a kind of obstruction). However, this method is more complicated and may require professional equipment and software support. 5. ** Use extinction cover (suitable for mobile phones)**: If you use a mobile phone to take photos, you can use the anti-reflection artifact-mobile phone hood, which is specially developed for mobile phone photography. When taking photos, you only need to stick close to the glass to physically eliminate the reflection of the glass. This kind of mobile phone extinction cover was divided into two models. No matter whether the camera was distributed in the middle or on the side, it could be adapted accordingly. The soft material of the silica gel did not hurt the phone and its good malleability made it suitable for most models on the market. 6. ** Adjusting the shooting method (suitable for cell phone or camera)**: Stick your cell phone or camera on the glass so that the reflection behind you will not be transmitted into the lens. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>
There were several ways to test the reflection of a car: 1. ** Light intensity test **: This is one of the common methods to evaluate the reflective performance of a car. The reflective performance of the reflective material was evaluated by measuring the reflected light intensity of the reflective material under the illumination of light. 2. ** Viewing angle test **: It mainly measures the reflective effect of reflective materials under different viewing angles. During the test, a viewing angle tester is usually used to measure and evaluate its reflective performance. 3. ** Durability Test **: This test is designed to evaluate the durability and reliability of the reflective material in the long-term use process. The durability and reliability of reflective materials were evaluated by simulating exposure and usage conditions during long-term use. <a href="/?from=ask_words" style="color:red" target="_blank">Read more exciting novels for free</a>